Ajout de configs
This commit is contained in:
parent
0c233bf494
commit
8ef1d9c4d4
|
|
@ -0,0 +1,144 @@
|
|||
## Configuration file for CAVA. Default values are commented out. Use either ';' or '#' for commenting.
|
||||
|
||||
|
||||
[general]
|
||||
|
||||
# Smoothing mode. Can be 'normal', 'scientific' or 'waves'. DEPRECATED as of 0.6.0
|
||||
; mode = normal
|
||||
|
||||
# Accepts only non-negative values.
|
||||
framerate = 60
|
||||
|
||||
# 'autosens' will attempt to decrease sensitivity if the bars peak. 1 = on, 0 = off
|
||||
# new as of 0.6.0 autosens of low values (dynamic range)
|
||||
# 'overshoot' allows bars to overshoot (in % of terminal height) without initiating autosens. DEPRECATED as of 0.6.0
|
||||
; autosens = 1
|
||||
; overshoot = 20
|
||||
|
||||
# Manual sensitivity in %. Autosens must be turned off for this to take effect.
|
||||
# 200 means double height. Accepts only non-negative values.
|
||||
; sensitivity = 100
|
||||
|
||||
# The number of bars (0-200). 0 sets it to auto (fill up console).
|
||||
# Bars' width and space between bars in number of characters.
|
||||
;bars = 0
|
||||
;bar_width = 1
|
||||
;bar_spacing = 0
|
||||
|
||||
|
||||
# Lower and higher cutoff frequencies for lowest and highest bars
|
||||
# the bandwidth of the visualizer.
|
||||
# Note: there is a minimum total bandwidth of 43Mhz x number of bars.
|
||||
# Cava will automatically increase the higher cutoff if a too low band is specified.
|
||||
; lower_cutoff_freq = 50
|
||||
; higher_cutoff_freq = 10000
|
||||
|
||||
|
||||
|
||||
[input]
|
||||
|
||||
# Audio capturing method. Possible methods are: 'pulse', 'alsa', 'fifo' or 'sndio'.
|
||||
# Defaults to 'pulse', 'alsa' or 'fifo', in that order, dependent on what support cava was built with.
|
||||
#
|
||||
# All input methods uses the same config variable 'source'
|
||||
# to define where it should get the audio.
|
||||
#
|
||||
# For pulseaudio 'source' will be the source. Default: 'auto', which uses the monitor source of the default sink
|
||||
# (all pulseaudio sinks(outputs) have 'monitor' sources(inputs) associated with them).
|
||||
#
|
||||
# For alsa 'source' will be the capture device.
|
||||
# For fifo 'source' will be the path to fifo-file.
|
||||
method = pulse
|
||||
source = auto
|
||||
|
||||
; method = alsa
|
||||
; source = hw:Loopback,1
|
||||
|
||||
; method = fifo
|
||||
; source = /tmp/mpd.fifo
|
||||
|
||||
|
||||
|
||||
[output]
|
||||
|
||||
# Ouput method. Can be 'ncurses', 'noncurses' or 'raw'.
|
||||
# 'noncurses' is for systems that does not suport ncurses.
|
||||
# 'raw' is a 16 bit data stream of the bar heights that can be used to send to other applications.
|
||||
# 'raw' defaults to 200 bars, which can be adjusted in the 'bars' option above.
|
||||
; method = ncurses
|
||||
|
||||
# Visual channels. Can be 'stereo' or 'mono'.
|
||||
# 'stereo' mirrors both channels with low frequencies in center.
|
||||
# 'mono' averages both channels and outputs left to right lowest to highest frequencies.
|
||||
; channels = stereo
|
||||
|
||||
# Raw output target. A fifo will be created if target does not exist.
|
||||
; raw_target = /dev/stdout
|
||||
|
||||
# Raw data format. Can be 'binary' or 'ascii'.
|
||||
; data_format = binary
|
||||
|
||||
# Binary bit format, can be '8bit' (0-255) or '16bit' (0-65530).
|
||||
; bit_format = 16bit
|
||||
|
||||
# Ascii max value. In 'ascii' mode range will run from 0 to value specified here
|
||||
; ascii_max_range = 1000
|
||||
|
||||
# Ascii delimiters. In ascii format each bar and frame is separated by a delimiters.
|
||||
# Use decimal value in ascii table (i.e. 59 = ';' and 10 = '\n' (line feed)).
|
||||
; bar_delimiter = 59
|
||||
; frame_delimiter = 10
|
||||
|
||||
|
||||
|
||||
[color]
|
||||
|
||||
# Colors can be one of seven predefined: black, blue, cyan, green, magenta, red, white, yellow.
|
||||
# Or defined by hex code '#xxxxxx' (hex code must be within ''). User defined colors requires a
|
||||
# terminal that can change color definitions such as Gnome-terminal or rxvt.
|
||||
; background = black
|
||||
; foreground = '#008080'
|
||||
|
||||
# Gradient mode, only hex defined colors are supported, background must also be defined in hex
|
||||
# or remain commented out. 1 = on, 0 = off. Warning: for certain terminal emulators cava will
|
||||
# not able to restore color definitions on exit, simply restart your terminal to restore colors.
|
||||
gradient = 1
|
||||
gradient_count = 3
|
||||
gradient_color_1 = '#008080'
|
||||
gradient_color_2 = '#D58E00'
|
||||
gradient_color_3 = '#D50000'
|
||||
|
||||
|
||||
|
||||
[smoothing]
|
||||
|
||||
# Percentage value for integral smoothing. Takes values from 0 - 100.
|
||||
# Higher values means smoother, but less precise. 0 to disable.
|
||||
; integral = 70
|
||||
|
||||
# Disables or enables the so-called "Monstercat smoothing" with or without "waves". Set to 0 to disable.
|
||||
; monstercat = 1
|
||||
; waves = 0;
|
||||
|
||||
# Set gravity percentage for "drop off". Higher values means bars will drop faster.
|
||||
# Accepts only non-negative values. 50 means half gravity, 200 means double. Set to 0 to disable "drop off".
|
||||
; gravity = 100
|
||||
; gravity = 200
|
||||
; gravity = 0
|
||||
|
||||
|
||||
# In bar height, bars that would have been lower that this will not be drawn.
|
||||
; ignore = 0
|
||||
|
||||
|
||||
[eq]
|
||||
|
||||
# This one is tricky. You can have as much keys as you want.
|
||||
# Remember to uncomment more then one key! More keys = more precision.
|
||||
# Look at readme.md on github for further explanations and examples.
|
||||
; 1 = 1 # bass
|
||||
; 2 = 1
|
||||
; 3 = 1 # midtone
|
||||
; 4 = 1
|
||||
; 5 = 1 # treble
|
||||
|
||||
|
|
@ -0,0 +1,41 @@
|
|||
local utils = require "mp.utils"
|
||||
|
||||
del_list = {}
|
||||
|
||||
function contains_item(l, i)
|
||||
for k, v in pairs(l) do
|
||||
if v == i then
|
||||
mp.osd_message("undeleting current file")
|
||||
l[k] = nil
|
||||
return true
|
||||
end
|
||||
end
|
||||
mp.osd_message("deleting current file")
|
||||
return false
|
||||
end
|
||||
|
||||
function mark_delete()
|
||||
local work_dir = mp.get_property_native("working-directory")
|
||||
local file_path = mp.get_property_native("path")
|
||||
local s = file_path:find(work_dir, 0, true)
|
||||
local final_path
|
||||
if s and s == 0 then
|
||||
final_path = file_path
|
||||
else
|
||||
final_path = utils.join_path(work_dir, file_path)
|
||||
end
|
||||
if not contains_item(del_list, final_path) then
|
||||
table.insert(del_list, final_path)
|
||||
end
|
||||
end
|
||||
|
||||
function delete()
|
||||
for i, v in pairs(del_list) do
|
||||
print("deleting: "..v)
|
||||
os.remove(v)
|
||||
end
|
||||
end
|
||||
|
||||
mp.add_key_binding("ctrl+DEL", "delete_file", mark_delete)
|
||||
mp.register_event("shutdown", delete)
|
||||
|
||||
|
|
@ -0,0 +1,13 @@
|
|||
[redshift]
|
||||
temp-day=4500
|
||||
temp-night=3400
|
||||
|
||||
transition=1
|
||||
|
||||
location-provider=manual
|
||||
|
||||
adjustment-method=randr
|
||||
|
||||
[manual]
|
||||
lat=48.10038
|
||||
lon=-1.66612
|
||||
|
|
@ -0,0 +1,61 @@
|
|||
#!/bin/sh
|
||||
|
||||
# Set brightness via xbrightness when redshift status changes
|
||||
|
||||
# Set brightness values for each status.
|
||||
# Range from 0 to 100 is valid
|
||||
brightness_day="100"
|
||||
brightness_transition="60"
|
||||
brightness_night="20"
|
||||
max=$(cat /sys/class/backlight/intel_backlight/max_brightness)
|
||||
actual=$(cat /sys/class/backlight/intel_backlight/actual_brightness)
|
||||
|
||||
case $1 in
|
||||
period-changed)
|
||||
case $3 in
|
||||
night)
|
||||
for (( c=$actual; c > $((( $brightness_night * $max / 100))); c-=1 ))
|
||||
do
|
||||
echo $c > /sys/class/backlight/intel_backlight/brightness
|
||||
sleep .2
|
||||
done
|
||||
;;
|
||||
transition)
|
||||
old="$2"
|
||||
if [[ "$old" == "none" ]]
|
||||
then
|
||||
if [[ $actual -lt $(( $brightness_transition * $max / 100 )) ]]
|
||||
then
|
||||
old="night"
|
||||
else
|
||||
old="daytime"
|
||||
fi
|
||||
fi
|
||||
case $old in
|
||||
night)
|
||||
for (( c=$actual; c < $((( $brightness_transition * $max / 100))); c+=1 ))
|
||||
do
|
||||
echo $c > /sys/class/backlight/intel_backlight/brightness
|
||||
sleep .2
|
||||
done
|
||||
;;
|
||||
daytime)
|
||||
for (( c=$actual; c > $((( $brightness_transition * $max / 100))); c-=1 ))
|
||||
do
|
||||
echo $c > /sys/class/backlight/intel_backlight/brightness
|
||||
sleep .2
|
||||
done
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
daytime)
|
||||
for (( c=$actual; c < $((( $brightness_day * $max / 100))); c+=1 ))
|
||||
do
|
||||
echo $c > /sys/class/backlight/intel_backlight/brightness
|
||||
sleep .2
|
||||
done
|
||||
echo $max > /sys/class/backlight/intel_backlight/brightness
|
||||
;;
|
||||
esac
|
||||
;;
|
||||
esac
|
||||
|
|
@ -0,0 +1,6 @@
|
|||
#!/bin/sh
|
||||
|
||||
case $1 in
|
||||
period-changed)
|
||||
exec dunstify -u low -r $(sum <<<"redshift" | cut -d' ' -f1) "Redshift" "Period changed to $3"
|
||||
esac
|
||||
|
|
@ -0,0 +1,12 @@
|
|||
[Unit]
|
||||
PartOf=mpd.service
|
||||
After=mpd.service
|
||||
Requires=mpd.service
|
||||
Description=MPD Notifications
|
||||
|
||||
[Service]
|
||||
ExecStart=/home/breizh/.local/bin/mpd-notif
|
||||
Restart=on-failure
|
||||
|
||||
[Install]
|
||||
WantedBy=default.target
|
||||
Loading…
Reference in New Issue